Page 1 of 1

? S&W Mod41 Technical Question - Bolt Irregularity

Posted: Thu Nov 17, 2011 9:37 am
by Mountain Man
On my 4 month old S&W Model 41 (700-800 rounds,) I have noticed a small "bump" rising above the surrounding surface at the rear underside of my bolt (see pic.) Maybe a welding spot?? There is a corresponding elongated mark running up the face of the hammer. So, the "bump" is the bearing point as the hammer is cocked.

Should I smooth this "bump" out - say, with a Dremel followed by fine paper? Or, should I just leave it as is?

Image

Posted: Thu Nov 17, 2011 3:26 pm
by blue68f100
I normally use a thin film of grease on my center fires where the hammer contacts the slide. It helps it slide with less friction when it comes back. Unless the slide is very hard you will have it and there is not much you can do. I would leave it as it is. It gives you a larger contact area which will eventually get to where it stops. Now if your hammer has a rough spot it may help to smooth it out.

Posted: Thu Nov 17, 2011 3:56 pm
by Mountain Man
blue68f100 wrote:I normally use a thin film of grease on my center fires where the hammer contacts the slide. It helps it slide with less friction when it comes back. Unless the slide is very hard you will have it and there is not much you can do. I would leave it as it is. It gives you a larger contact area which will eventually get to where it stops. Now if your hammer has a rough spot it may help to smooth it out.
Thanks! Actually, it makes for a smaller contact area. If the bump were not there, the contact would be across the wider area of the bolt. You can see where the contact starts across the entire edge but, as soon as the "bump" comes into contact, it is the only thing touching the hammer and runs up what is becoming a groove.

Posted: Thu Nov 17, 2011 7:51 pm
by Bullseye
I would stone that bump flat with the underside of the bolt. That is not a normal protrusion. The abnormal wear on your hammer is visual evidence of the problem. Take care to make the underside smooth or further damage can ensue to the hammer.

R,
Bullseye

Thanks!

Posted: Sat Nov 19, 2011 12:14 pm
by Mountain Man
Thanks! I certainly appreciate your attention and response!

As I continue to think about it, the protrusion has not only marked the hammer face but riding up and resting on the hammer could be a contributing (or major) factor in the malfunctions experienced during the 4 months I have owned the gun, i.e., annoying and consistent failures to eject when using SV ammo. It certainly has caused increased resistance to cycling and may explain why the gun has only functioned perfectly when using HV ammo.

Not owning a stone nor knowing how to use one, this has tipped the balance to make me send the gun back to S&W for correction and general attention to the malfunctions. And, of course, I don't want to void the warranty. By the way, this is a Performance Center gun!

Image

Posted: Sat Nov 19, 2011 2:42 pm
by Bullseye
In that case, they will likely replace the bolt and the hammer. I would also mention the inconsistent ejections in my comments to S&W customer service.

R,
Bullseye

Posted: Sat Nov 19, 2011 4:13 pm
by Mountain Man
Bullseye wrote:In that case, they will likely replace the bolt and the hammer. I would also mention the inconsistent ejections in my comments to S&W customer service.

R,
Bullseye
Will do! And plead with them to NOT change the trigger which I adjusted and now clicks smoothly at 2 lb 2oz. Hopefully, they can change the hammer without disturbing the sear and trigger.

Posted: Sun Nov 20, 2011 1:20 pm
by Bullseye
Not in the cards, when changing the hammer they'll have to re-cut the hooks to go with your sear's engagement contour. This may change your settings, I'd let them know you want a little over two pounds trigger pull and they'll adjust it for you in the performance shop.

R,
Bullseye

Back from S&W

Posted: Wed Dec 14, 2011 5:51 pm
by Mountain Man
My "new" S&W Performance Center Model 41 was returned from S&W today. Do you suppose they have some objective to drive you crazy? I sent them a full page starting with a summary that mentioned 1-the bump/protrusion on the bottom of the slide; 2- the failures to extract/eject/fully cycle on SV ammo; and, 3- the observed abnormal friction points showing wear on the gun after less than 1,000 rounds. This summary was followed by three paragraphs detailing those findings. In the box they returned was a paper that said,
"CUSTOMER COMPLAINT: EJECTION
REPAIRED: ADJUST EJECTOR"

That's it! That's all they said! When I opened it up, it was apparent that they did stone off the bump from the bottom of the slide. I can't see that they relieved any of the friction points and I can't see what they did to the ejector?? The hammer has not been touched.

I'm not sure when I can get it to the range, with Xmas and all, but I guess the proof will be whether I still have the problems.

Posted: Wed Dec 14, 2011 11:09 pm
by Bullseye
Sometimes they are deliberately vague on their descriptions for repairs. I don't know what they're current shop backlog is running but time is money, and the less time you spend writing the more time you have for money making.

R,
Bullseye

Posted: Thu Dec 15, 2011 1:35 pm
by ruger22
Ruger can be vague, too. I sent a Single-Six back to Ruger for a .011 cylinder/barrel gap. I got it back with a .004 gap. The work order said my complaint was "spitting". It said barrel and pawl "repaired" and listed five screws as "replaced".

I know they rebarreled it. I assume they also found less than perfect timing, so that meant a new pawl and frame screws.

Posted: Fri Dec 16, 2011 11:08 am
by piasashooter
As Ruger22 stated, I experienced the same vagueness with Ruger a while back when I sent in a MKIII. Everything turned out fine for me, so try not to get to far ahead of yourself, I know I was jumping to conclusions, when in reality everything was fine. Like you said, you will have to wait until you get to the range. Hope it all works well for you.

Range Report

Posted: Mon Dec 19, 2011 6:02 pm
by Mountain Man
My Mod 41, fresh back from warranty work at S&W, went to the range today. At first, I was in a panic - the first magazine, with 5 rounds of CCI SV, required manual ejection and feed with every round! Then, I recalled that I had re-installed the factory 7.5lb recoil spring before sending it in. Luckily, I had brought the 7.0lb Wolff spring with me. I put it in the 41 and never experienced another glitch of any sort for 150 rounds!

Posted: Mon Dec 19, 2011 7:38 pm
by blue68f100
Good to hear your gun is fixed. Even though they did not document all the work.

Posted: Mon Dec 19, 2011 8:58 pm
by jstanfield103
Great news MountianMan, the factory spring may just need a few more rounds through it, or you may just put it in and open up the slide and leave it sit that way for a couple of day's. But who cares you have it fixed and the wolf spring seems to have the job at hand.
Great news!