Could this work for you?
http://www.mil-dot.com/Mil_Dot_User_Guide.htm#MilDots
Search found 30 matches
- Wed Mar 31, 2010 7:55 pm
- Forum: Rifle Forum
- Topic: Extreme tactical scopes
- Replies: 16
- Views: 13550
- Wed Mar 31, 2010 6:11 pm
- Forum: The Reloading Bench
- Topic: RCBS hand primer
- Replies: 16
- Views: 17160
- Sun Mar 21, 2010 8:54 pm
- Forum: Rifle Forum
- Topic: Tikka
- Replies: 4
- Views: 5306
- Sat Mar 20, 2010 10:20 pm
- Forum: Rimfire Rifles
- Topic: New Henry .22 LR
- Replies: 10
- Views: 8040
- Sat Mar 20, 2010 4:23 pm
- Forum: Handgun Forum
- Topic: 1911 sights
- Replies: 5
- Views: 4431
I was thinking the same thing with the locktite this morning after the wife shot it. They set the sights for the ammo you shoot, and they did that right for sure. Was able to get a hold of Gunsite this morning as well and they said the same thing, that the slight movement isn't an issue, but if it w...
- Fri Mar 19, 2010 10:41 pm
- Forum: Handgun Forum
- Topic: 1911 sights
- Replies: 5
- Views: 4431
- Fri Mar 19, 2010 9:57 pm
- Forum: Handgun Forum
- Topic: 1911 sights
- Replies: 5
- Views: 4431
1911 sights
I just got my Colt govt xse back from the smith, I had Novak night sights put on. They had to mill the slide front and rear as it only had the factory 3 dots. The front sight is loose in the dovetail, I can barely move it with my finger and they installed a very small roll pin down through the top o...
- Sat Feb 27, 2010 8:24 pm
- Forum: Trading Post
- Topic: WTB Ruger Talo grips
- Replies: 0
- Views: 21749
WTB Ruger Talo grips
I'd like to buy a set of the Talo grips for the ruger mkIII, not the multi colored USA grips. I'd also consider any of the wood grips with the Ruger logo done in wood.
I'd also like a factory SPORTER style stock for a 10/22.
I'd also like a factory SPORTER style stock for a 10/22.
- Tue Feb 16, 2010 5:21 pm
- Forum: Rimfire Rifles
- Topic: Remington mod 511
- Replies: 3
- Views: 4570
- Tue Feb 09, 2010 7:53 pm
- Forum: Rimfire Rifles
- Topic: Remington mod 511
- Replies: 3
- Views: 4570
Check the trigger and sear pivot pins and holes for wear, the sear pin rides in a slot on the trigger if I remember correctly. Also the hole in the receiver for the trigger pivot pin has a bur from the factory a lot of times on those rifles. Remove the bur and see if you have enough room to make shi...
- Mon Jan 04, 2010 10:44 pm
- Forum: Rifle Forum
- Topic: Tikka
- Replies: 4
- Views: 5306
Tikka
Opinions on, experiences with Tikka bolt guns? Looking into 300wsm.
- Tue Dec 15, 2009 8:50 pm
- Forum: Rimfire Handguns
- Topic: Iron vs. Fiber optic sights
- Replies: 4
- Views: 5116
Finally, something I can comment on... Get two drill bits, a 1/4" and a 3/8", and something with a 1/2" hole drilled in it. Now insert the 1/4" bit in the 1/2" hole and center it by eye then repeat with the 3/8" bit. The 3/8" is easier to center for most people because the eye and brain have less to...
- Tue Nov 24, 2009 7:10 pm
- Forum: Rimfire Handguns
- Topic: MKIII Sear pin
- Replies: 10
- Views: 6072
Thanks for the replies, a new factory pin is on it's way courtesy of Ruger. I've had good luck using drill bits for TEMP fixes in the past, I keep those smaller bits that break just for such an occasion to get by until the correct factory pin can be obtained. Ruger requested the broken pin back beca...
- Mon Nov 23, 2009 9:21 pm
- Forum: Rimfire Handguns
- Topic: MKIII Sear pin
- Replies: 10
- Views: 6072
- Mon Nov 23, 2009 5:41 pm
- Forum: Rimfire Handguns
- Topic: MKIII Sear pin
- Replies: 10
- Views: 6072
MKIII Sear pin
First off: New to this forum and I must say the info here is second to none, you guys are great. I've been lurking for a while now. I have a MKIII that I put a VQ kit in and it took care of my creep, but I wasn't inpressed with pull though the gun functioned fine. When I got home I decided that I wa...