12ga,10ga,8ga,4ga FH; 585HE, 700HE; Other Big bores--

This is a place to discuss shooting related topics and techniques.

Moderators: Bullseye, Moderators

hubel585
Regular contributor
Regular contributor
Posts: 71
Joined: Fri Nov 25, 2011 11:12 pm
Location: Brinton , MI

Post by hubel585 » Sun Sep 15, 2013 5:21 pm

Here is picture of our 12ga sabots with the marks that the barrel lands made, marked with
black marker. The one with narrow mark is Savage barrel and one with wide mark is
an Abolt barrel. And the ones fired in Savage and NEFs with the narrow lands the marks
impressed into the plastic getting good bite and not twisting the petals. The one from abolt
he used slower powder for easier start and it open petals ok, without twisting petals like
the faster powder did for him.

Image
..
Next is picture showing top edge of sabots. Our sabot on left you roll crimp down over
the inside of it a little . We have lots of them yet.
The other factory sabot they crimp real short and sharp
180 degree crimp down on top of it.

Image

We see a use for modified 585 application in Indiana deer hunting. Mainly shotgun only, but
they also allow rifles with over 35cal pistol calibers; and any over 35cal rifle with a case
1.8" or shorter, usually short wildcats. So we have the the 585 HI... The I is for Indiana.
Here is picture of it next to the kinda little 500 S&W. 585 HI holds over 80 gr powder.

Next picture is a Magtech chambered for it. Gets 440gr Minie over 2,100 fps.
The .585"- .587" Minies of 440gr, 540gr, etc work in it, and they're good deer slugs
We got other guns with it going into; bolt guns, like in the last picture,
single shots and checking couple lever actions.
Might work great in MNs many guys like....Ed

Image

Image

Image

hubel585
Regular contributor
Regular contributor
Posts: 71
Joined: Fri Nov 25, 2011 11:12 pm
Location: Brinton , MI

Post by hubel585 » Wed Oct 16, 2013 4:08 am

In above post we compare the top thickness of sabots
.Here is comparison of the thickness of the sides of two types of
brass 12ga cases, the RMC turned case and the thinner
Magtech drawn case. Easy to see you can't size with same dies
and sometimes you have to use different wads..

Image

In posts earler in the thread you saw variety of wad columns with
12ga sabots and here is picture of my favorite wads to go between
seal and sabot. The white felt ones from BPI. They compress down
evenly on firing, easy to load, decent price,

Image

You've seen the work on our 585HE posted. Folks ask what case
I made first ones from and how. Here is a sketch showing the steps
I used to make the first 585HE from long basic straight Nyati brass.
The start of the belt step I put on the case where it is thick I do it
in my case spinner lathe I made. Then case is lubed and run into
couple swaging/sizing dies and comes out formed into our belted,
straight sided, 585HE case...... It is really faster getting a big
run of cases made in a factory.


Image

Shot a 12ga sabot load w/440 gr Minie bullet in smoothbore Rossi
in 3" case, Going about 1700... .. 4" group 3 shots at 30 yds.
Gun works fine, shoots nice. Got extra weight in the butt.
The Minie I used is a semi-round nose. If I had the ones of same length
with blunt nose, slightly heavier the group size would be smaller as
they'd be more nose heavy, be like Foster slugs..Ed

hubel585
Regular contributor
Regular contributor
Posts: 71
Joined: Fri Nov 25, 2011 11:12 pm
Location: Brinton , MI

Post by hubel585 » Mon Dec 09, 2013 12:39 am

Here is picture of the group improvement a guy had shooting our
sabots in a real tight barrel. Actually an undersize barrel compared
to Savage and Nef barrels. Had a wide open group with shotgun
powder but made it much smaller using much more
of the slower 4759.

Image

There is a guy now in Canada with our sabots for guys there and
other countries, and as well, he can ship back to here. He plans
on supplying the .58cal slugs also for the sabots if guys can't get
them or don't cast their own.......
Contact is- jeff.a.white at gmail.com
If things work out for him he plans on getting a bunch
our 585 cases imported for guys to get there also.

I got some factory 8ga kiln loads, 3 oz lead at 1800 in the long
barrel falling block. Got box of 25 to see how they compared to the
loads we setup.They go faster in long barrel than in short kiln guns.
Our favorite is 900gr in the 8ga wadcup at 2300, in plastic case.

Image

Here is picture of section 585HE case showing 4 pyrodex 54cal,
60gr equivalent pellets, with a 440 gr Minie bullet.
Actual powder wt is about 185gr....Goes about 2600.
Nice cloud of smoke and really bellers out of the slow twist barrel
barrel we set up for minies.....Top pellet I tapered a little and fit it
inside the hollowbase of the bullet.That's how to get 4 pellets in....Ed

Image

hubel585
Regular contributor
Regular contributor
Posts: 71
Joined: Fri Nov 25, 2011 11:12 pm
Location: Brinton , MI

Post by hubel585 » Wed Jan 01, 2014 7:02 pm

Another use for 58cal Minie Bullets would be to setup a 24ga FH.
Minie bullets cheap to cast and buy. We use the .575-.577" in our
12ga sabot, and the .585-.587 in my 585HE. And you could use
577 NE bullets also.

For those in shotgun only areas there is a way. You can get 2.5"
Magtech brass cases, but also you can set up a 3" chamber and use
577NE 3" brass. Grafs shows some under 4 bucks each. Cheaper
than getting them made. And if you set up chamber with shotgun style
forcing cone you could shoot shorter Magtech as well as plastic cases.
Reason to use 577 cases, they are stronger solid head, last forever,
and can be run higher pressures and still last forever.
You can get barrels, 58cal at Green Mtn I think. .We got some also.

AND the first batch 585 barrels from McGowen has got here, more
will be built.They are the regular 1 to 20 twist barrels, and we have 14
that are profiled and polished, and 3 others that are straight blanks,
1 to 20 twist. And 6 slow twist barrel blanks for guys doing mainly
Minie bullet guns, and bunch smoothbore blanks...Pictures soon.

Here are couple pictures of a 585HE gun a guy is doing with nice
walnut stock. Gun has extra bedding lug and accra-glassed.
It is an Enfield and has single stack magazine.

Image

Image

hubel585
Regular contributor
Regular contributor
Posts: 71
Joined: Fri Nov 25, 2011 11:12 pm
Location: Brinton , MI

Post by hubel585 » Tue Jan 28, 2014 2:05 pm

Here is picture of 24ga FH in the Mossberg bolt gun. On a
Mossy 390 frame, .585" heavy barrel, same as 24ga size.
Chamber is set up 3" with shotgun style forcing cone,
so it can use 2.5" plastic cases and 2.5" Magtech brass
cases with slugs or shot and for 3" cases we use 577NE
3" brass. Really make a hairy 24ga using the 440gr to
540 gr Minie bullets at 21-2400. If you take 540 Minie bullet
mould and leave out base pin you'd have a 650gr that
would do. All these bullets and slugs as well as jacketed and
turned 577/585 bullets work in 24ga as well as my 585HE.
And the smaller Minies work in our 12ga sabots. I keep
saying 58cal is where it is at, and there are more bullet and
slug choices in the .585 size, easy to find, than any other
caliber over 458. And Minies are like 40 cents each and
cheaper if you cast your own.

Image


Here is picture .585" barrels from McGowen, with other barrels.
Most of the McGowens profiled and some straight blanks.
Others we have are the slow twist and smooth blanks...
In back some of the cases and die sets.

Image

Here is picture of an Enfield and a BBK in Hogue recoil
reducing stocks. These stocks are the rubber coated ones with
the easy to grip, nice pistol grip.Has McGowen 26 inch barrels,
1 to 20 twist, barrels are heavy profile and taper
to .980 inch at the muzzle. Guys are doing more Enfields
and other actions through the winter. Ed

Image

hubel585
Regular contributor
Regular contributor
Posts: 71
Joined: Fri Nov 25, 2011 11:12 pm
Location: Brinton , MI

Post by hubel585 » Sun Feb 23, 2014 4:24 pm

Some guys in 12ga like to use the Magtech brass cases
but the cases being brass the sides are thinner than
plastic, and that makes loose fit in 12ga chambers.
And cases expand a lot with heavier loaded slug
loads, are harder to resize, wear out quicker.
But I found that .750 hollowbase 10ga slug fits
those cases and still chambers in regular 12ga.
chamber, it isnt a sloppy fit.

So If you have a 12ga smooth barrel with full length
backbore job, of .850" bore or bigger you could use
the Magtech brass and .850" size 10ga hollowbase slugs.
Now these .850" slugs won't go in a 12ga plastic case
and chamber in regular 12ga chamber.And you do not
fire them through 12ga regular size barrel.

Brett in MN used the a BPI AQ slugs in his full length
backbored 12ga and got fair accuracy as he said the wads
under slugs expanded a lot for a decent fit.
The 10ga slug shown in the 2.5 inch Magtech is 800 gr,
and .850" diameter. These cases will take magnum
pressure so you can get good speed, for what this short
case can hold.

It is too bad they don't make 3" and 3.5" versions.
These 2.5" cases are easier to find and much less than
others, so if needing brass ones you can rig up guns
to work with them. To build a new barreled gun in actual
12ga size, IE .729" bore, you'd make chamber to
minimum specs so cases don't over expand.
In the picture are 2 10ga slugs on right, like in the case,
and 2 12ga jacketed slugs and one 12ga lead slug left.ED


Image



Here is the ytube URL again for our guy
shooting 585HE in his NEF----By mid summer we plan on a
pickup truck load of more 585HE cases coming in.

http://www.youtube.com/watch?v=HypaUdwQGAc

hubel585
Regular contributor
Regular contributor
Posts: 71
Joined: Fri Nov 25, 2011 11:12 pm
Location: Brinton , MI

Post by hubel585 » Thu Mar 13, 2014 10:24 pm

Here is good simple system with big hollowbase slugs to stop
the skirts from deforming, or wads getting pushed into
the hollow base. I found that dense dow foam works
good, I was using glue gun, but the dense foam is easier, cut
plugs out of foam sheet and force into the base. Make it a
tight fit, use spot of glue inside, glue that is for foam....
Trim off the foam flush..In picture is 10 ga 900gr slug
with foam pressed into the base..

Image

How we get good 24ga plastic seals with protusion on
top that fits up inside 58cal Minie base, same bore as 24ga
and our 585HE. I get the 24ga seal by cutting apart the BPI
24ga Brush wad, getting two seals out of each.Works great
in plastic case giving a shorter column than other seals and
wads, so we can get in enough of our 4759 for good speed.
The 24ga idea is getting nicer all the time with
the variety of cheap 58cal slugs, and good 3" brass cases,
drawn cases, we didn't have to wait to get made.
And all kind of guns we can use, bolt 395 Mossbergs, single
shots of all kinds, Autos,, pumps. bolt action Savage,
even 1887 Win and Greener MKIII, bolt action JC Higgins. .

Image

Here is picture Khan auto we setting up 24ga FH, it is 3.5"
model, has a 12ga barrel to change with. Being 3.5" it
feeds/ejects through lengthened port 3" brass 24ga cases we
made from 577NE brass. We rework back of the bolt for
slightly longer stroke.Ed

Image

hubel585
Regular contributor
Regular contributor
Posts: 71
Joined: Fri Nov 25, 2011 11:12 pm
Location: Brinton , MI

Post by hubel585 » Wed Apr 23, 2014 9:23 pm

Here is picture of 24ga cases, loads; and some slugs and seals.
Brass cases are 3", plastic cases are 2.5". Brass 3" can be loaded
to match 577NE power.

Image

Here is of 24ga in an 87 Win, just test gun of mine. Uses same barrels
as our 585HE, This one has slow twist for Minie bullets.Our guys
have got supply of regular and slow twist barrels.

Image

Here is picture of the first 585HE done and shooting in Australia.
It is owned by the poster, 'tankhunter' on the AR forums.
Built by his smith who has a reamer.
Guys there can get cases from Bertram, and there will soon be three
reamers there. There is a company there now making 585 barrels,
Allan and Grant Swan. in Redbank, Queensland.....Ed

Image

hubel585
Regular contributor
Regular contributor
Posts: 71
Joined: Fri Nov 25, 2011 11:12 pm
Location: Brinton , MI

Post by hubel585 » Sun Aug 17, 2014 2:01 am

Finally got back to forums.Been busy with 24ga FH and 585HE
and getting 585HE cases made, as many as possible...

We are now working a bit with 24ga FH and here is picture
of it with our 585HE case. Both use same bullets/slugs, same
bore barrels. Main use difference, 24ga FH easy setup in break
actions and 585HE in bolt actions and falling blocks.

Image

Picture of non-discarding 585/24ga sabot cup I found that holds
458 bullets and slugs tight. It had hammerhead type slug in it that
was pulled out, wouldn't stay in tight after pulled. Sabot was a loose fit
in 20ga, though made for 20ga, but small, so I shrunk the bottom rib,
fits perfect, super tight, in 24ga and 585HE. A press in fit gives
good resistance for good ignition.

Image

Here is another 24ga/585 sabot that holds .452" 45cal pistol
bullets. Made by Hornady for 58cal Muzzle loaders..
With 250 gr bullet in 585HE hot load will go about mach 4.

Image

Here is easy way to weight plastic stocks with hollow butts, use rubber
coated computer mouse balls, weight comes out perfect without being
too heavy if using that much lead.And coating keeps them quiet, and
we hold them in with piece dense foam under butt pad....Ed

Image

greener

Post by greener » Tue Aug 19, 2014 7:34 am

Nice rounds.

Where do you get the computer mouse balls?

hubel585
Regular contributor
Regular contributor
Posts: 71
Joined: Fri Nov 25, 2011 11:12 pm
Location: Brinton , MI

Post by hubel585 » Tue Aug 19, 2014 8:21 pm

Family has a computer, electronics, etc, recycling/repair business

and I got a bunch of them. Just setting in a pail, and I tried

some in hollow stock and worked great. So I stopped the

peeling off of the rubber for steel balls for slingshots, and

now save them all for weight. Find recycling places/junk yards

that take in computer stuff. Ed

hubel585
Regular contributor
Regular contributor
Posts: 71
Joined: Fri Nov 25, 2011 11:12 pm
Location: Brinton , MI

Post by hubel585 » Wed Sep 10, 2014 1:52 pm

First AUS buffalo killed by 585HE. By Tankhunter with his Ruger #1.

If you use closeup on picture, you see loaded round on the buffs hide

next to the 585HE Ruger #1.... A nice heavy barreled gun..Ed

Image


I put the 585 in a Savage 112, lots of room lengthwise, figuring out an
extractor is a problem, but then got a look at the savage 212, the 12 ga
one with big diameter bolt and locking lugs. Its locking lugs are bigger
than the lugs in a big PH bolt action. So one day will do one
on a Savage 212, and adjusting extractor to fit no problem...Ed

Image

hubel585
Regular contributor
Regular contributor
Posts: 71
Joined: Fri Nov 25, 2011 11:12 pm
Location: Brinton , MI

Post by hubel585 » Sat Oct 25, 2014 1:30 pm

Here is picture of 585HE 100 cases loaded, CEB solid nose bullets
and hollowpoints. This bullet is a turned solid with wide meplat
or wide hollowpoint. .

Image

Here is picture of triball loads that fellows like for deer and hogs,
and just general tear em up fun, with using BPGS seal to improve
sealing under what are heavier loads. The balls are .600" and
315gr. each. The wadcup is a TUPRW123 that Precision sells.

Image

I need a bunch of empty 3.5" 20ga plastic cases.


Our 585 caliber is modern bolt action continuance of the 577 Nitro
Express rimmed case, that many big game hunters like, usually
set up in double rifles. It has an interesting history, from the old 24ga
size to 577NE, to 585 Nyati with G&A picture of Ross Seyfreid
shooting one in a Ruger #1 under recoil knocking his shooting glasses
off, to the Trex of internet fame knocking guys over with recoil,
to our 585HE the strongest yet.

The 577NE is an offshoot of 24 gauge caliber paper cases, only they went
eventially to brass cases. Back in the 1860-70s, starting first with short
cases and black powder, cases built like shotgun cases, called the
577 Snider, then going to coiled brass cases, still with black powder,
then on to drawn brass cases, called 577 BP Express. then to 3"
and other longer cases with smokeless. The Snider started out with a bullet
of .570" diameter and through the progression to the 577NE bullet
diameter ended up at .585". This general bore diameter of cartridge guns
and muzzle loaders, it is really interesting on how they developed
and were used by military and then hunters over the years. The Snider
was necked down to make the 577-450 , a military round used all
over the British Empire, by the tens of millions.

Bases of both 24ga and 577NE are about the same. Now we have made a
24ga FH, a slight regression to earlier times, by taking 577NE brass, and
reducing rim diameter to 24ga specs. Two minute job. And
stamp the caseheads 24 ga.

For shotgun upgrading in power and range, It is all about increasing
the power in easy to find brass cases, stronger actions, and finding
reasonable price rifled barrels. Same barrels we found for 585, work for 24ga.
The 577NE brass we make 24ga drawn cases from, for example are
about a third the cost of 600NE brass, or getting turned 24ga cases made.
We could use 24ga thin cases but they are a pain, expand way too much,
with slug loads which makes resizing without crumpling cases a problem.

Info about the power in types of guns normally set up with 24ga FH,
break actions, bolt shotguns,etc. In thin brass 24ga case, 440gr slug
goes 1500, with about 2000 ft lbs, that's in a 2.5" Magtech brass case.
Now using the better, heavier 3" brass we got, we can increase speed
to 1750 fps increasing energy 50%, going to 2000 fps about doubles
energy. And going to 2300 which good brass holds ok, in heavy barrel
gun, gets us near 2 1/2 times the energy. About 37-40,000 psi which the
actions hold in this smaller diameter case, compared to 12 gauge size.
So makes relatively smaller bore shotgun, 24ga, with 458WIN power.
.Perfect with Minie bullets. Perfect for deer and hogs, bear, etc.

Great for slug hunting in shotgun only areas. We mark barrels 24ga
and cases 24. A decent case that is complimentary to our 585HE....Ed

hubel585
Regular contributor
Regular contributor
Posts: 71
Joined: Fri Nov 25, 2011 11:12 pm
Location: Brinton , MI

Post by hubel585 » Fri Dec 19, 2014 10:30 pm

Guys asking about using 585 CEB bullet in our 12ga super
sabot. Here is picture, We just took off the bottom band and couple
middle bands on the CEB and it fit perfect in our 12ga sabot,
which uses .575" slugs. Hollowpoint one pictured 700gr in the
sabot loaded in brass case. Can be used in plastic case with a
special made hollowed out long roll crimper.

Image

Getting some more interest in our 585HE.
An application for our 585 HE is for guys with old military 14.5mm
PTRDs, to use our case with chamber insert. In many places 14.5
cases are scarce, real expensive, as well as most 14.5mm cases
being steel are not the easiest to resize/reload. Our case sizes
like regular cases and can be easily reloaded many times.

And a PTRD with almost a 5 foot long barrel could get 650gr
spitzer bullet to about same speed the 14.5mm gets a 900 gr using
3 times as much powder. About 3300 fps. Or get a 900gr at 2800.
Great possibilities for fun shooting. For tactical use in a place
where it would be useful to reload in the operations field, where
steel cases are scarce. 100 of our cases do over 2000 reloads.

Image

I like Enfields to put our 585HEs in, for reasonable cost guns, the
actions once sporterized are one of the longest for long cases. .
Here is inexpensive way to fancy up the Enfield Bolt handle by
cutting the dogleg part of the old handle off and welding on
inexpensive contoured handles I found, one of which is like
Ruger 77 handle, the one on the right . Something even a novice
like me can do.....

Image

A lot of guys are crazy about CEB bullets. Here are light 450gr
ones in our 24ga FH. That hollowpoint can range in weight 450gr
to 700gr depending on how much we cut off the back..
The 24ga FH brass case is nice complement to our 585HE,
for shotgun only deer hunters that want a .585" caliber,
and easy to find big bore bullets.... Ed

Image

hubel585
Regular contributor
Regular contributor
Posts: 71
Joined: Fri Nov 25, 2011 11:12 pm
Location: Brinton , MI

Post by hubel585 » Sat Feb 14, 2015 11:13 am

For lightweight plinking, deer hunting, etc, in 585HE as well as 24ga FH
here is picture of 58cal Hornady sabot that holds .451/.452" light
bullets 225 to 300 gr. A way to shoot targets economically. Low recoil
but a big bang and satisfaction. A 250 gr bullet would go about
mach 4 with a top load..

Image

Here is what 585 bull barrel, target blank looks like, 1 5/8" OD and 32" long.
It'll go in heavy action of some kind. 4th one from the left. The one in yellow
sleave on top, is a heavy contoured one with muzzle of .980". we got a
bunch of them and so does McGowen.

Image


Here is picture, nice cast bullet I like for the 585HE and 24ga FH.
It is .585" diameter and 650 gr and these particular ones are a
hard lead alloy, plus they've been heatreated. They are about as
hard as copper jacketed softs pivtured. These in .575'' size would
work in our 12ga sabot..

Image

But to penetrate good and do great damage to game or target they
can be fairly soft lead and hollowbase like Minie Bullets. Here is picture
of timber drilled through with .585 soft lead Minie from 585HE.
Picture is the back of 6x6 timbers where Minie bullets came out.

Image

Guys experimenting with multiple ball loads in 12ga wadcups, here is a
way to keep them together group wise.Ed


Image

Post Reply